Service can be used for different situations please add booking notes and state application and if you have devices or would like us to provide.

Please indicate I.e. Heat, Smoke, CO detectors and quantities thx

Add on service

Only to be used when booking other services otherwise a minimum of 1/2 hour will be charged at our prevailing rate

To install a cable run normally swa fixed to a fence or run under ground 16/32 amp Supply , with a IP rated outlet switch double pole

Customer to install trench if required

Based on the following assumptions made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

- Spare capacity in existing distribution board with sufficient amperage if applicable


Should you be unsure please arrange for time only appointment for an assessment, consultation

-To install a new electrical supply from pre-Existing electrical system, surface mounted
-To install a switch fuse Spur Point

Electrical Certification

Methods

- Clipped direct, Surface mounted, and or trunking (Upgrades available)

The following assumptions are made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

- Spare capacity in existing distribution board with sufficient amperage

Should you be unsure please arrange for time only appointment for an assessment, consultation

To Replace Faulty Light pull Switch

Only to be used when booking other services otherwise a minimum of 1/2 hour at our prevailing rate will be charged

Service can be used for different situations please add booking notes and state application and if you have devices or would like us to provide.

Please indicate I.e. Heat, Smoke, CO detectors and quantities thx



IF BOOKING ONLY ONE ITEM —-Only to be used when booking other services otherwise a minimum of 1/2 hour at our prevailing rate will be charged

6-Install Replacment Electric Socket Fronts

Add on service

Only to be used when booking other services otherwise a minimum of 1/2 hour at our prevailing rate will be charged

-To install electrical supply surface
-To carry out electrical testing / commissioning of installed works

Based on the following assumptions made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

Should you be unsure please arrange for time only appointment for an assessment, consultation

4-To Remove Old Light Fittings (make safe with connectors block)

Based on the following assumptions made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

- Spare capacity in existing distribution board with sufficient amperage if applicable


Should you be unsure please arrange for time only appointment for an assessment, consultation

To Install a like for like security light to a maximum hight 4 Meters flood light or lantern

These fittings are inexpensive, cheap to run and fairly easy to fit. With the Part P regulations that are in force you may need to use the services of a qualified electrician. I would supply the unit via a 13 amp switch fuse spur with the fuse downgraded to 2 or 3 amp dependant on the lamp wattage, this is for two

SEE DATAIL SECTION FOR MORE INFORMATION

4a-To disconnect and make safe old redundant domestic alarm internal External Boxes

Add on service

Only to be used when booking other services otherwise a minimum of 1/2 hour will be charged at our prevailing rate

Parts to be charged as used added to final Invoice

-To install associated cable up to 5m from pre-existing external light for electrical switch internal or external surface install.

Based on the following assumptions made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

- Spare capacity in existing distribution board with sufficient amperage if applicable

Should you be unsure please arrange for time only appointment for an assessment, consultation

To Install New Domestic Fuse-board 18th Edition With RCBO,S and SPD

Price vary £299 to £349 plus materials.
Please note there will be extra costs if the main meter tails need updating they will be added to the final Invoice .

Typical Cost With Parts And Testing £1145 + vat including electrical testing on three bedroom house

Based on the following assumptions made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations i.e. earthing arrangements.

- Property has recent electrical test EICR report within last 2 years otherwise an Electrical Installation Condition Inspection will need to take place with report.

If this is incorrect new earthing systems will need to be installed to incoming Gas / Water services

Should you be unsure please arrange for time only appointment for an assessment, consultation

Lights not included-

Includes removal and making safe central light ( if applicable ) more than 3 lights installed

Installation of electrical wiring for lighting on existing switching arrangements

Installation and connection of appropriate lights for intended area I.e IP rating and Fire Rating

Additional notes

No additional labour costs with upgrading to High Efficency type I.e LED speak to engineer

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

- Spare capacity in existing distribution board with sufficient amperage if applicable

Should you be unsure please arrange for time only appointment for an assessment, consultation

Typical cost labour £45 per light discretionary discount for more than 6 lights

To disconnect / remove existing electrical hob
To assemble / install new electrical hob
Supplemental costs may be applicable if wooden worktop needs to be altered to accommodate new hob
This price is for connect to existing supply , (like for like ). providing the outlet supplies are satisfactory.

Based on the following assumptions made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

- Spare capacity in existing distribution board with sufficient amperage if applicable



Should you be unsure please arrange for time only appointment for an assessment, consultation

Please note not to be used for Unvented Hot Water system bookings.

-To isolate / drain hot cold water storage systems
-To disconnect / remove old immersion heater
-To assemble / install new electrical immersion heater

Includes testing fault diagnostics draining, removal, installation, Re-filling and electrical safety testing.

Based on the following assumptions made

- The existing hot water tank is in a good serviceable condition and not got existing damage.
- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

- Spare capacity in existing distribution board with sufficient amperage if applicable


Should you be unsure please arrange for time only appointment for an assessment, consultation

-To install one new electrical point for outside socket from pre-existing supply or distribution board

-To install outside IP socket with or without RCD protection based on existing system please let us know you can send a picture of your distribution board if you are unsure


Based on the following assumptions made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

- Spare capacity in existing distribution board with sufficient amperage if applicable

Should you be unsure please arrange for time only appointment for an assessment, consultation


Correctly installed, an exterior socket is a very useful facility to have. It means you no longer have to run extension leads from inside the house, with the potential for tripping over them!

It enables you to run electric garden equipment such as a lawn mower, hedge trimmer and various other items including power tools, in a far safer way. In fact it is wise to have one at the back and one at the front of the property, which can be used for car washing equipment, power washers and other items such as vacuum cleaners.

This must incorporate RCD Protection

USE THIS SERVICE ONLY FOR NONE EMERGENCY FOUR DAYS AHEAD LOCAL WORK PETERBOROUGH ONLY.


Analyse Information – decide the probable cause based on past experience & training
Investigate – now attempt to find the fault from your analysis
Rectify –
( If Possible) note )

found, safely repair the fault if possible.
Test – when the fault is put right & restored, test your work before re-energising

USE THIS SERVICE ONLY FOR NON EMERGENCY FOUR DAYS AHEAD LOCAL WORK PETERBOROUGH ONLY.


Analyse Information – decide the probable cause based on past experience & training
Investigate – now attempt to find the fault from your analysis
Rectify –
( If Possible) note )

found, safely repair the fault if possible.
Test – when the fault is put right & restored, test your work before re-energising

Note this price is for a like for like straight connection assumptions that the existing are in tack and correct , If the connection point is not in a suitable position and needs to be moved then extra costs will apply

15-Install New Dimmer Switch (like for like).
Certain assumptions made

Back box is deep enough to house the dimmer.

Add on service

Only to be used when booking other services otherwise a minimum of 1/2 hour at our prevailing rate will be charged

Although you can increase the number of sockets in a room by converting single sockets to doubles, there may be times when you need an extra socket where none exist already. In this case, you'll need to add a spur from a ring circuit. You can either run this from an existing socket, or from a junction box that's connected into the cable run of a suitable ring circuit. The circuit must have RCD protection.

Surface installation means plastic boxes and trunking mounted to the wall

Flush means flat to the wall buried cables in the wall or building fabric .

To Install a Switch adjacent to loft hatch , and Install a single baton or ceiling rose above or near hatch

Labor: From £399 + VAT
Typical Project Total: ~£1,000 + VAT (including materials)
​What’s Included
​Distribution: New consumer unit (fuseboard) in the outbuilding.
​Outlets: Installation of three socket points and one lighting point.
​Cabling: SWA (Armoured) or T&E cabling as required for the site.
​Safety: Full commissioning and Electrical Installation Certificate (EIC).
​Technical Assumptions
​Existing Board: Assumes your main house board has sufficient spare capacity and load headroom.
​Safety Standards: Existing installation must meet BS 7671 (specifically RCD protection and earthing).
​Materials: Billed separately based on current market rates and cable run length.
​Note: For a fixed-price survey, load verification, or bespoke design, please book our "Technical Help & Consultation" service first.
​Key Site-Visit Points

To install electrical point for towel rail / heater bathroom

To Install a like for like security light to a maximum hight 4 Meters flood light or lantern

These fittings are inexpensive, cheap to run and fairly easy to fit. With the Part P regulations that are in force you may need to use the services of a qualified electrician. I would supply the unit via a 13 amp switch fuse spur with the fuse downgraded to 2 or 3 amp dependant on the lamp wattage, this is for two reasons : –

SEE DATAIL SECTION FOR MORE INFORMATION

If you need any extra TV points for additional televisions, within any room, these can usually be connected to your current aerial system. Multiple TV Points can be installed to as many rooms as you require, anywhere in your home, even the garage. Extra TV Points, use good quality digital ready RG6 cable which reduces interference and produces excellent picture quality, we can even re-run an old outlet that may have dated or inferior cable.

The equipment boxes to be surface mounted only .

Add on service

Only to be used when booking other services otherwise a minimum of 1/2 hour will be charged at our prevailing rate

The following assumptions are made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.