Add on service

Only to be used when booking other services otherwise a minimum of 1/2 hour will be charged at our prevailing rate

The following assumptions are made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

39-Relocate Wall Switch (Two Meters ) to Dry wall only .

The following assumptions are made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

Kitchen & Bathroom Wall Mounted Fan Heater + Timer
options to add blow heater on in basket

The following assumptions are made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

The following assumptions are made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

-To install surface electric supply clipped direct, conduit or SWA armoured cable
-Installation of charger
-To carry out electrical testing / issue certification.


The following assumptions are made

- Spare capacity in existing distribution board and switchgear components available otherwise new distribution board will be required with sufficient amperage

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

Should you be unsure please arrange for time only appointment for an assessment, consultation

The following assumptions are made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

This price is for replacing a (like for like ), light fitting at a maximum height 2.4 meters normal domestic ceilings . It dose not include assembling light fittings .

Please assemble them prior to our visit thank you

Please note a light fitted in a vaulted ceiling would cost a little extra POA .

The following assumptions are made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

This price is for replacing a (like for like ), light fitting at a maximum height 2.4 meters normal domestic ceilings . It dose not include assembling light fittings .

Please assemble them prior to our visit thank you

29-To Install Replacment Ceiling Rose or Batton Holder

Add on service

Only to be used when booking other services otherwise a minimum of 1/2 hour will be charged at our prevailing rate

The following assumptions are made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

Methods

- Clipped direct, Surface mounted, and or trunking (Upgrades available)

The following assumptions are made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

- Spare capacity in existing distribution board with sufficient amperage

Should you be unsure please arrange for time only appointment for an assessment, consultation

Hot Zone
The hot zone, this is the area directly above your cooker or hob, and can have high humidity or get wet. Ensure that this area is free from flammable items including wood, wallpaper, plug sockets, wiring or an overhanging boiler.

Assuming all existing connection and wiring meet current standards just a straight forward connection only , Any alterations we be charged extra.

This service is for a replacement distribution board for outbuilding such as a garage, office in a domestic setting with 2-4 circuits.

The following assumptions made

Pre-existing sub-main and associated circuits are present and have been previously in service or commissioned with certification from approved electrical contractor.

The incoming supply is sufficient amperage for intended purpose

To install associated wiring for a new light point and electrical switch including the installation of a light fitting such as a strip light.


Based on the following assumptions made

- This can be a spur or a new circuit from the local distribution board providing spare capacity available

- Clipped direct / surface

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

-To carry out electrical safety checks and testing on relevant affected circuits or accessories following a recent water leak
-To make safe / establish if circuits or accessories can be re-energised or safe to be left on

Issue report / provide consultation

Based on the following assumptions made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

Based on the following assumptions made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

To Fit door bell to wall/door /install power supply for unit


No electrical parts included charged as used and added to invoice

7a-Investigate / testing on immersion heater(s) faults insulation tests

To carry out investigation and fault diagnostics procedures
Investigate the circuit, supply, switchgear, Heater carry out electrical fault diagnostics tests

Provide consultation write report where required of findings.

Service can be used for different situations please add booking notes and state application and if you have devices or would like us to provide.

Please indicate I.e. Heat, Smoke, CO detectors and quantities thx

Add on service

Only to be used when booking other services otherwise a minimum of 1/2 hour will be charged at our prevailing rate

To install a cable run normally swa fixed to a fence or run under ground 16/32 amp Supply , with a IP rated outlet switch double pole

Customer to install trench if required

Based on the following assumptions made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

- Spare capacity in existing distribution board with sufficient amperage if applicable


Should you be unsure please arrange for time only appointment for an assessment, consultation

-To install a new electrical supply from pre-Existing electrical system, surface mounted
-To install a switch fuse Spur Point

Electrical Certification

Methods

- Clipped direct, Surface mounted, and or trunking (Upgrades available)

The following assumptions are made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

- Spare capacity in existing distribution board with sufficient amperage

Should you be unsure please arrange for time only appointment for an assessment, consultation

To Replace Faulty Light pull Switch

Only to be used when booking other services otherwise a minimum of 1/2 hour at our prevailing rate will be charged

Service can be used for different situations please add booking notes and state application and if you have devices or would like us to provide.

Please indicate I.e. Heat, Smoke, CO detectors and quantities thx



IF BOOKING ONLY ONE ITEM —-Only to be used when booking other services otherwise a minimum of 1/2 hour at our prevailing rate will be charged

6-Install Replacment Electric Socket Fronts

Add on service

Only to be used when booking other services otherwise a minimum of 1/2 hour at our prevailing rate will be charged

-To install electrical supply surface
-To carry out electrical testing / commissioning of installed works

Based on the following assumptions made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

Should you be unsure please arrange for time only appointment for an assessment, consultation

4-To Remove Old Light Fittings (make safe with connectors block)

Based on the following assumptions made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

- Spare capacity in existing distribution board with sufficient amperage if applicable


Should you be unsure please arrange for time only appointment for an assessment, consultation

To Install a like for like security light to a maximum hight 4 Meters flood light or lantern

These fittings are inexpensive, cheap to run and fairly easy to fit. With the Part P regulations that are in force you may need to use the services of a qualified electrician. I would supply the unit via a 13 amp switch fuse spur with the fuse downgraded to 2 or 3 amp dependant on the lamp wattage, this is for two

SEE DATAIL SECTION FOR MORE INFORMATION

4a-To disconnect and make safe old redundant domestic alarm internal External Boxes

Add on service

Only to be used when booking other services otherwise a minimum of 1/2 hour will be charged at our prevailing rate

Parts to be charged as used added to final Invoice

-To install associated cable up to 5m from pre-existing external light for electrical switch internal or external surface install.

Based on the following assumptions made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

- Spare capacity in existing distribution board with sufficient amperage if applicable

Should you be unsure please arrange for time only appointment for an assessment, consultation

To Install New Domestic Fuse-board 18th Edition With RCBO,S and SPD

Price vary £299 to £349 plus materials.
Please note there will be extra costs if the main meter tails need updating they will be added to the final Invoice .

Typical Cost With Parts And Testing £1145 + vat including electrical testing on three bedroom house

Based on the following assumptions made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations i.e. earthing arrangements.

- Property has recent electrical test EICR report within last 2 years otherwise an Electrical Installation Condition Inspection will need to take place with report.

If this is incorrect new earthing systems will need to be installed to incoming Gas / Water services

Should you be unsure please arrange for time only appointment for an assessment, consultation

Lights not included-

Includes removal and making safe central light ( if applicable ) more than 3 lights installed

Installation of electrical wiring for lighting on existing switching arrangements

Installation and connection of appropriate lights for intended area I.e IP rating and Fire Rating

Additional notes

No additional labour costs with upgrading to High Efficency type I.e LED speak to engineer

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

- Spare capacity in existing distribution board with sufficient amperage if applicable

Should you be unsure please arrange for time only appointment for an assessment, consultation

Typical cost labour £45 per light discretionary discount for more than 6 lights

To disconnect / remove existing electrical hob
To assemble / install new electrical hob
Supplemental costs may be applicable if wooden worktop needs to be altered to accommodate new hob
This price is for connect to existing supply , (like for like ). providing the outlet supplies are satisfactory.

Based on the following assumptions made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

- Spare capacity in existing distribution board with sufficient amperage if applicable



Should you be unsure please arrange for time only appointment for an assessment, consultation

Please note not to be used for Unvented Hot Water system bookings.

-To isolate / drain hot cold water storage systems
-To disconnect / remove old immersion heater
-To assemble / install new electrical immersion heater

Includes testing fault diagnostics draining, removal, installation, Re-filling and electrical safety testing.

Based on the following assumptions made

- The existing hot water tank is in a good serviceable condition and not got existing damage.
- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

- Spare capacity in existing distribution board with sufficient amperage if applicable


Should you be unsure please arrange for time only appointment for an assessment, consultation

-To install one new electrical point for outside socket from pre-existing supply or distribution board

-To install outside IP socket with or without RCD protection based on existing system please let us know you can send a picture of your distribution board if you are unsure


Based on the following assumptions made

- Based on existing electrical installation meeting a minimum safety standard as defined by the electrical regulations with regards to RCD protection and earthing arrangements.

- Spare capacity in existing distribution board with sufficient amperage if applicable

Should you be unsure please arrange for time only appointment for an assessment, consultation


Correctly installed, an exterior socket is a very useful facility to have. It means you no longer have to run extension leads from inside the house, with the potential for tripping over them!

It enables you to run electric garden equipment such as a lawn mower, hedge trimmer and various other items including power tools, in a far safer way. In fact it is wise to have one at the back and one at the front of the property, which can be used for car washing equipment, power washers and other items such as vacuum cleaners.

This must incorporate RCD Protection

USE THIS SERVICE ONLY FOR NONE EMERGENCY FOUR DAYS AHEAD LOCAL WORK PETERBOROUGH ONLY.


Analyse Information – decide the probable cause based on past experience & training
Investigate – now attempt to find the fault from your analysis
Rectify –
( If Possible) note )

found, safely repair the fault if possible.
Test – when the fault is put right & restored, test your work before re-energising

USE THIS SERVICE ONLY FOR NON EMERGENCY FOUR DAYS AHEAD LOCAL WORK PETERBOROUGH ONLY.


Analyse Information – decide the probable cause based on past experience & training
Investigate – now attempt to find the fault from your analysis
Rectify –
( If Possible) note )

found, safely repair the fault if possible.
Test – when the fault is put right & restored, test your work before re-energising